ServicesEquipment Installation
Pool Equipment Installation in Phoenix
We replace pumps, filters, heaters and salt systems at your home, but only after we confirm why the old part stopped working. That way the new equipment is sized to your pool, plumbed neatly and built to last through long summers of daily run time.
New equipment, chosen for the right reason
A failing pump is not always a bad pump. Sometimes it is a clogged impeller, a tired capacitor or a filter so loaded it starves the motor. Before we recommend anything new, we test the equipment pad and find the real cause. If a repair will do, we say so and point you to our pool repair service instead.
When replacement is the right call, we match the new unit to your pool's volume, plumbing size and how you use the water. Our technicians are CPO certified, so the water chemistry and circulation side of the decision gets the same attention as the hardware. Pool Cleaning Phoenix is ROC licensed for this work.
What an installation includes
- 01
Variable-speed pumps
Most replacement pumps now are variable-speed. We program separate speeds for filtering, cleaning and any water features, so the pump spends most of the day running slow and quiet rather than flat out.
- 02
Filters of every type
Cartridge, DE and sand filters each handle desert dust and hard water in their own way. We help you choose the type that suits your pool and the upkeep you prefer, then size it to the pump so pressure stays in a healthy range.
- 03
Heaters and heat pumps
A gas heater brings the water up to temperature fast. A heat pump is slower but cheaper to operate through the milder months. Before recommending either, we check your gas service, your electrical panel and how often you actually swim.
- 04
Salt chlorine generators
We mount the cell and control board, bring the water to the correct salt level and show you how to read the display. Scale buildup is what wears salt cells out here, so we explain how to keep yours clear.
- 05
Automation and timers
A controller can schedule the pump, heater, lights and cleaner. We wire it, label every circuit and show you the settings on the panel or your phone.
- 06
Clean plumbing and fittings
Fresh unions, square-cut glued joints and pipe held up off the ground. A neat pad is easier to service and less prone to drips.
Questions about Equipment Installation?
Call(602) 632-0630Signs your equipment may need replacing
A pump that whines or just hums
A high-pitched whine or a grinding sound usually means the motor bearings are worn. If the motor hums but won't turn, the cause may be a capacitor or a seized motor, and we find out which before we quote a new pump.
Pressure that won't settle
When the filter gauge climbs soon after a cleaning, or the tank shows cracks, the filter or its internals may be near the end of their life.
A heater that short-cycles
Constant on and off, error codes or soot around the burner tray are reasons to stop using a gas heater until it has been inspected.
Cloudy water despite good chemistry
If the readings look right but the water stays dull, the pump or filter often can't move the full volume through fast enough.
Rising power bills
An older single-speed pump running eight hours or more a day through summer uses a lot of electricity. A well-programmed variable-speed pump can bring that down noticeably.
How installation day runs
- 1
Diagnosis and quote
We test the existing equipment, measure the plumbing and note your electrical and gas supply. You get a written quote by phone with each part and the labor listed.
- 2
Shutdown and removal
We turn off power at the breaker, isolate the pad and remove the old unit. Anything we take out leaves with us.
- 3
Fit and plumb
The new equipment is set level, plumbed with fresh fittings and wired to code. If the job needs a new circuit or gas work that requires a permit, we tell you before work begins.
- 4
Start-up and testing
We prime the system, check for leaks at every joint, confirm flow and pressure and program the schedule. Then we walk you through the controls and leave the pad swept clean.
What shapes the price of new equipment
Your pool and your equipment pad usually matter more to the price than the brand on the box. We check these details during the visit, so the quote you hear covers the job as it really is and nothing gets tacked on afterward.
- Unit type and capacity
- A bigger pump, a high-output heater or a controller with several circuits costs more than an entry-level model. We match capacity to your pool instead of selling you horsepower you will never use.
- Plumbing changes
- When the new unit lines up with the old connections, the swap is simple. Mismatched pipe sizes, a rerouted line or extra valves add parts and time.
- Electrical and gas work
- Running a longer wire, adding a breaker or bringing a gas line to a new heater takes extra labor. Some of that work also calls for a permit, which we flag before you decide.
- Pad access and condition
- Narrow side yards, a cracked slab or lines buried under gravel can slow the install. We point these out at the first visit so they are part of the quote.
Equipment installation questions
Will you tell me if my pump can be repaired instead?
Yes. Plenty of pumps only need a new shaft seal, bearing or capacitor. We test first, and when a repair is the sensible choice we quote that rather than a whole new pump.
Is a variable-speed pump worth it in Phoenix?
For most pools, yes. Summer means many hours of run time each day, and a variable-speed pump draws much less power at the low speeds where it spends most of that time. We set the schedule so the water circulates well without paying for wasted horsepower.
Can you install equipment I bought myself?
In many cases we can. We compare the model to your pool size and plumbing before fitting it, so you know ahead of time whether it will do the job well.
How much of my day will the work take?
Replacing a pump or filter on its own is normally done within a few hours. Heaters, salt systems and automation that need fresh wiring or gas work run longer, and we tell you the expected time along with your quote.
Do I need to be home?
Not for most of it, as long as we can get to the equipment pad and the breaker. We do like to show you the new controls when we finish, so we can schedule that part around you.
Find out what your equipment really needs
We'll look at the whole pad, explain what failed and quote the right replacement for your home. Serving Phoenix, Scottsdale, Tempe and nearby communities.